You are here: Home> Catalogue> Ball Bearings

Ball Bearings

Ball Bearings Model: Ball Bearings Technology standard /Miniature, MR series /6000, 6200, 6300, 6400 series / 6800, 6900, 6700 series / 1600, 16000 60/22 series / R series / RLS, RMS series / 62200, 62300, 63000, W series / 8000, 87000, 88000 series / 5200, W series / Hanging , Mast guide series / Agricultural machinery bearings

Online Order Print this page Showing 1-5 of 3, total pages 1 2 3 4 5

Radial Bearing (Except Tapered Roller Bearings) Inner Ring P6 (ABEC3) Unit:µm Nominal Bore Diameter (mm) Over Up to 0.61) 2.5 2.5 10 10 18 18 30 30 50 50 80 80 120 120 150 150 180 180 250 250 315 315 400 400 500 500 630 630 800 800 1000 1000 1250 Bore, Cylindrical Deviation dmp3) 0 -7 0 -7 0 -7 0 -8 0 -10 0 -12 0 -15 0 -18 0 -18 0 -22 0 -25 0 -30 0 -35 0 -40       Variation Vdp Diameter Series 9 9 9 9 10 13 15 19 23 23 28 31 38 44 50       0¡¤1 7 7 7 8 10 15 19 23 23 28 30 38 44 50       2¡¤3¡¤4 5 5 5 6 8 9 11 14 14 17 19 23 26 30       Variation Vdmp 5 5 5 6 8 9 11 14 14 17 19 23 26 30       Width Deviation Bs4) 0 -40 0 -120 0 -120 0 -120 0 -120 0 -150 0 -200 0 -250 0 -300 0 -300 0 -350 0 -400 0 -450 0 -500       Width Variation VBS 12 15 20 20 20 25 25 30 30 30 35 40 45 50       Ridial Runout Kia 5 6 7 8 10 10 13 18 18 20 25 30 35 40         Radial Bearing (Except Tapered Roller Bearings) Inner Ring P0 (ABEC3) Unit:µm Nominal Bore Diameter (mm) Over Up to 2.52) 6 6 18 18 30 30 50 50 80 80 120 120 150 150 180 180 250 250 315 315 400 400 500 500 630 630 800 800 1000 1000 1250 1250 1600 1600 2000 Bore, Cylindrical Deviation dmp3) 0 -7 0 -7 0 -8 0 -9 0 -11 0 -13 0 -15 0 -18 0 -20 0 -25 0 -28 0 -33 0 -38 0 -45 0 -60       Variation Vdp Diameter Series 9 9 9 10 11 14 16 19 23 25 31 35 41 48 56 75       0¡¤1 7 7 8 9 11 16 19 23 25 31 25 41 48 56 75       2¡¤3¡¤4 5 5 6 7 8 10 11 14 15 19 21 25 29 34 45       Sealed Type Bearing 2.3.4.10 9 9 10 13 16 20 25 30                     Variation VDmp 5 5 6 7 8 10 11 14 15 19 21 25 29 34 45       Ridial Runout Kss 8 8 9 10 13 18 20 23 25 30 35 40 50 60 75           The width tolerances ¡÷Cs and VCs are same as VBs of inner ring, respectively. Note The larger ¡÷dmp and the smaller ¡÷dmp in the table do not apply when the width of raceway face is within 1.2 times the maximun fillet radius. Annotations 1)Includes 0.6mm 2)Includes 2.5mm 3)Applies only to cylindricalinner diameter bearings 4)Contact TSB for ¡÷Bs and ¡÷Cs of bearings Pairs

Online Order Print this page

Showing 1-5 of 3, total pages

1 2 3 4 5

DYS Corporation Phone Number: (86-576) 8247-9090 (4L) Fax Number: (86-576) 8241-2588 / 8290-8290 E-mail: info@dysmail.com